GJP100W.MG is a 1 Gang, 200 Watt (100 Watts for LEDs) Power Grid Dimmer module for Varilight, MK, Schneider/GET, and Crabtree power grid plates.

GTIN: 5021575969047
£31.08  (ex. VAT)
£27.97 (ex. VAT)
£33.56 (inc. VAT)
Earn 31 Reward Points when you buy this item
Share this page to get 5% discount
Free Delivery on all orders over 100 GBP

  •    Description
  •    Reviews
  •    Q & A (2)
  •    Shipping & Returns
V-Pro Series 1 Gang (Single), 1 or 2 Way 200 Watt (Trailing Edge) Dimmer Module for varilight Power Grid

This Power Grid module has all the same ingenuity as the rest of the Varilight V-Pro Series LED Dimmers, in addition this module has been re-designed to fit into any Varilight, MK, Schneider/GET, and Crabtree Power Grid. The GJP100W.MG can be used in a 1 or 2 Way circuit, it controls lamps up to a maximum of 200 Watt (100 watts for LEDs), it has a Push on/Push off action. This Power Grid Module dimmer has Trailing Edge technology. Eliminate Dimmer Buzz For GLS Bulbs, GU10 Lamps, and LV Transformers Including Trailing Edge Loads

VARILIGHT Dimmer Switches have an industry-wide reputation for exceptional performance, long life and innovation at attractive prices.

The VARILIGHT V-Pro (Professional Universal) Series Dimmer (also known as the J Dimmer), like all our products, is designed to meet the latest European Safety Legislation.

The V-Pro Series were primarily designed for Dimmable LED's, the dimmers, with a minimum load of only 10 Watts, can operate at least 1-10 good quality Dimmable LED's, it works especially well with the manufacturers, Megaman.

These Dimmers can also be used to operate upto 8 Varilight (YCA20D) or Megaman Dimmable Energy Saving Lamps, (Please refer to the instruction leaflet of the Megaman lamps for usage tips).

The V-Pro Series Dimmers can also be used for Mains Voltage Lighting, Trailing and Leading Edge Loads, and Electronic Low Voltage Transformers. The V-Pro Series, eliminates Dimmer Buzz For GLS Bulbs, GU10 Lamps, and LV Transformers Including Trailing Edge Loads and is equipped with Self Re-setting Overload Protection, so is able to handle overload situations, for example, if the wattage of the bulbs/lamps are accidentally too high on a circuit. This is achieved by the dimmer cutting out before there is any damage, (if the watts are grossly overloaded), until the load is reduced. The dimmer also contains a heat sensor which again stops damage to the dimmer, if it becomes too hot.

The V-Pro Series Dimmer has Soft Start Technology, allowing a longer life span of the bulbs or lamps used by increasing the brightness level softly, which also creates a welcoming effect.

When using Electronic Low Voltage transformers we recommend that a maximum of 5 good quality dimmable electronic transformers are used (10 if Varilight) with this Dimmer range. Please note: add the watts of the bulbs/lamps if using Varilight Transformers, to determine which dimmer to select, but if using another manufacturer of transformer, add up the VA of the transformers so it does not exceed the maximum of the dimmer.

The V-Pro Series Dimmers can also be used for mains incandescent GLS lamps (standard mains light bulbs), GU10 Lamps or similar Hi Spot Mains Halogen lamps, (only use quality UK supplied lamps), up to the maximum load as specified on the dimmer.

The V-Pro Series Dimmer can NOT be used for wire-wound Low Voltage transformers, Fans or inductive loads.

The V-Pro Series uses Trailing and Leading edge technology, please refer to leaflet for details on how to change between Leading and Trailing edge modes.

These Dimmers can be used in 2-way circuits (where one lighting circuit is controlled from two locations). In order to achieve 2-way switching, they must be paired with a standard 2-way switch in the other location. 3-way switching can also be achieved by adding an intermediate switch in to the circuit. Please note, if total dimming is preferred from all switched locations, in a 2 or 3-way circuit then choose the Varilight Touch and Remote Series range of dimmers, or the Eclique range (if dimming LEDs) in conjunction with Slave Dimmers.

This Dimmer has a maximum of 200 Watts per dimming module (100 Watts for LEDs) and a minimum of 10 Watts

Please see the Compatibility guide in "Specs & PDF's" for information about how many dimmer modules are allowed per power grid plate.


-Max Load 200 Watt (100W if using LEDs)

-Min Load 10 Watt

-Fits in a 35mm Deep Power Grid Wall Box

-To clean product we recommend only using a microfibre cloth.

-Barc: 5021575960501

-Power Grid PDF
-Compatibility 2013 PDF

There are currently no any reviews about this product.

Good afternoon,
Have an order to place for 12 pieces of the GJP100W.MG and would like to know if you are prepared to offer a discount for this quantity. I'm returning customer, but have been quoted a better price elsewhere!
Many thanks in advance.
Please email us if you haven't already. Please also let me know which website you saw the product on and the cost of them please. Email me paul@myswitchshop.com, thanks.

Does this item work on legrand products also?

We This product only is compatible with Varilight, MK, Schneider/GET, and Crabtree

All orders are packed & shipped from our HQ in West Sussex the same day you order, if in stock and ordered before 12pm GMT Monday to Friday. That's just how we like to roll!

Ask a question about the GJP100W.MG is a 1 Gang, 200 Watt (100 Watts for LEDs) Power Grid Dimmer module for Varilight, MK, Schneider/GET, and Crabtree power grid plates.

top ↑